Use for water filled plastic (including PEX) or metal pipes. Not use for anything else, like empty water pipes, fuel lines, hoses, gutters, steam lines and so on. Two year limited quality . If you are not completely satisfied with HEATIT heating cable, please don’t hesitate to contact our customer service in any time, we’ll try our best to solve your issues.
Pre-assembled easy to install. Including grounded plug with light, built in thermostat, and instructions. Easy to install and use. 120 volt, 7 watts/ft. Built in thermostat to turn the cable 37F on 50F off. Energy saving. 100% screen rate with the Aluminum foil and tinned copper braid.
Both CSA and ETL approved. Industrial grade heat shrinkage tube for connection. Tough XLPE as inner insulation and weather resistant PVC (high-low temperature) as out jacket.
Maximum 1/2 in fiberglass insulation was used over the heating cable for lower temperature protection. Pipes must be at least 3 feet and at least 3/8” and less than 1 1/2” in. diameter. No crossing. No spiral. No overlap itself. Only straight.
Testing the cable before the installation. Uncoil the cable, plug in the heating cable and then put the thermostat part of the cable into an ice bucket for few minutes. When the temperature is below 37F, the thermostat will energize the cable to work. Normally you can feel the slight warm on the heating cable in few minutes. To avoid the overheat, please don’t plug in the cable for a long time for testing. When you feel the slight warm, please turn it off.
JHSF doesn’t work unless the ambient temperature is below 37F/3 degree C. Please test the cable in a cold environment. HEATIT is registered Trademark by zhukeshi(We didn’t authorize other sellers in Amazon.com).
Suitable for use on plastic and metal water pipes.( including inlet pipe,drain pipe, sewer , palm tree frost protection etc). Self regulating heating cable output will adjust automatically based on the ambient temperature at each point along the cable. No worry about the overheat risk. More Safe. Can be used by straight, spiral and overlap. More functional.
Pre-assembled, easy to install. Including grounded plug with light, built in thermostat(turn the cable 37F on 50F off), and instructions. 120 volt, 3 watts/ft at 50 degrees F. Energy-efficient. Protect pipes up to 2″ in diameter. For a better freeze protection, at least 1/2 inch thick insulation material is recommended, especially for extremely cold weather.
ETL approved. 2 ft 18/3 cold lead with plug. Industrial grade heat shrinkage tube for connection.The lowest installation temperature of this heating cable is -10 degree C. Tough XLPE as inner insulation and weather resistant PE (high-low temperature) as out jacket. Ingress Protection 65. Durable
Testing the cable before the installation. Uncoil the cable, plug in the heating cable and then put the thermostat part of the cable into an ice bucket for few minutes. When the temperature is below 37F, the thermostat will energize the cable to work. Normally you can feel the slight warm on the heating cable in few minutes. Four year limited warranty. If you are not completely satisfied with HEATIT heating cable, please feel free to contact us in any time, we’ll try our best to solve your issue
3. Frost King HC30A Heating Cables, 30 Feet, Black
This item is a M-D Building Products 4309 3-Foot Pipe Heating Cable with Thermostat
Purpose of use for Rough Plumbing, pipe-heat-cables
This product is manufactured in China
Prevents frozen water pipes to -50°F
Easy to install just “wrap around” application
Sensor light shows thermostat is working
Available in 6 different lengths
Built in thermostat
Description
Product Description
This item is a M-D Building Products 4309 3-Foot Pipe Heating Cable with Thermostat. Purpose of use for Rough Plumbing, pipe-heat-cables. This product is manufactured in China.
From the Manufacturer
M-d building products 04309 3′ pipe heating cable with thermostatm-d building products 04309 3′ pipe heating cable with thermostat features: ul and csa approved pipe heating cable designed to prevent water line freeze up ready to install, grounded cord and plug, thermostat controlled, with pilot light 3′. No wrap needed.
Easy Heat AHB-019 9′ Pipe Heating CableEasy Heat AHB-019 9′ Pipe Heating Cable Features: Tough PVC inner insulation Continuous ground braid Weather resistant PVC outer jacket Energy saving Thermostat is located between cold lead and heating cable 2′ 18/3 cold lead with grounded plug 63 watts 120 volts AC 9′ heated section
From the Manufacturer
Temperature-controlled cable runs straight along pipe and valves, held in place by application tape and plugs into grounded electrical outlet. Keeps water flowing down to -380. For odd lengths of pipe over 3/4 inches in diameter, we recommend two separate cables on opposite sides of the pipe with up to 3 feet of overrun at center of pipe run. Metal pipe requires 1/2-inch fiberglass insulation around cable. For plastic pipe, its recommended wrapping pipe with aluminum foil before cable installation. The traditional resistance cable produces a fixed amount of heat based on the electrical line feed. It comes with a built-in thermostat that switches the flow of electricity on and off based on temperature. 120 volts. 7 watts per foot. Not U.L. Listed.
HEATIT is registered Trademark by zhukeshi(We didn’t authorize other sellers in Amazon.com). Suitable for use on plastic and metal water pipes( including inlet pipe,drain pipe, sewer, palm tree frost protection etc). Industrial grade self regulating heating cable. The cable output will adjust automatically based on the ambient temperature at each point along the cable. No worry about the overheat risk. More Safe. Can be used by straight, spiral and overlap. More functional.
Protect pipes up to 2 1/2” in diameter. For a better freeze protection, at least 1/2 inch thick or thicker insulation material is recommended, especially for extremely cold weather. If the ambient temperature is lower than -20°F(-29°C), please use 1” thick insulation material.
ETL approved. 50 degrees F for pipe freeze protection.3 ft 18/3 cold lead with grounded plug.
Roof deicing application: Can be used on flat roofs, metal roofs, asphalt roofs, rubber roofs, slate roofs, stone roofs, metal roofs, ceramic roofs, composite (tar and gravel) roofs and so on. Rated 10W/ft at 32°F (0°C) for roof deicing. For roof deicing application, you may need to buy clips and hangers separately. For the circuit breaker requirement especially for the cables which length is over 100ft, please check the listed picture.
Testing the cable before the installation. Uncoil the cable, plug in the heating cable. Normally you can feel the slight warm on the heating cable in few minutes. Two year limited warranty – If you are not completely satisfied with HEATIT heating cable, please feel free to contact us in any time, we’ll try our best to solve your issue.
HEATIT is regisred Tradeark by zhukhi(We didn’t ahorize other sellers in Amazon.com). Suitable for use on plastic and metal water pipes( including inlet pipe,drain pipe, sewer, palm tree frost protection etc). Industrial grade self regulating heating cable. The cable output will adjust automatically based on the ambient temperature at each point along the cable. No worry about the overheat risk. More Safe. Can be used by straight, spiral and overlap. More functional.
Fluoropolymer (One of the most heavy-duty plastic material) as the out jacket. Can be used underwater application. Please keep the connection (waterproof IP65) between the orange cold lead and black heating cable above the water. The black heating cable including end seal meets waterproof IP68. JHSF9-CT cables are configured for use in nonhazardous and hazardous locations, including areas where corrosives may be present.
Protect pipes up to 2 1/2″ in diamter. For a better freeze protction, at least 1/2 inch thick or thicker insulation material is recommended, especially for extremely cold weather. If the ambient temperature is lower than -20°F(-29°C), please use 1″ thick insulation material. Pre-assembled, Including grounded plug with light, easy to install install and use without built in thermostat. 120 volt, 5 watts/ft at 50 degrees F for pipe freeze protection.
Roof deicing appliction: Can be used on flat roofs, metal roofs, asphalt roofs, rubber roofs, slate roofs, stone roofs, metal roofs, ceramic roofs, comosite (tar and gravel) roofs and so on. Rated 10W/ft at 32°F (0°C) for roof deicing. For roof deicing application, you may need to buy clips and hangers separately.
Testing the cable before the instlation. Uncoil the cable, plug in the heting cable Normally you can feel the slight warm on the heating cable in few minutes. Two year limited warranty – If you are not completely satisfied with HEATIT heating cable, please feel free to contact us. in any time, we’ll try our best to solve your issue.
Conclusion
By our suggestions above, we hope that you can found Heatit Pipe Heating 30Ft for you.Please don’t forget to share your experience by comment in this post. Thank you!
Use for water filled plastic (including PEX) or metal pipes. Not use for anything else, like empty water pipes, fuel lines, hoses, gutters, steam lines and so on. Two year limited quality . If you are not completely satisfied with HEATIT heating cable, please don’t hesitate to contact our customer service in any time, we’ll try our best to solve your issues.
Pre-assembled easy to install. Including grounded plug with light, built in thermostat, and instructions. Easy to install and use. 120 volt, 7 watts/ft. Built in thermostat to turn the cable 37F on 50F off. Energy saving. 100% screen rate with the Aluminum foil and tinned copper braid.
Both CSA and ETL approved. Industrial grade heat shrinkage tube for connection. Tough XLPE as inner insulation and weather resistant PVC (high-low temperature) as out jacket.
Maximum 1/2 in fiberglass insulation was used over the heating cable for lower temperature protection. Pipes must be at least 3 feet and at least 3/8” and less than 1 1/2” in. diameter. No crossing. No spiral. No overlap itself. Only straight.
Testing the cable before the installation. Uncoil the cable, plug in the heating cable and then put the thermostat part of the cable into an ice bucket for few minutes. When the temperature is below 37F, the thermostat will energize the cable to work. Normally you can feel the slight warm on the heating cable in few minutes. To avoid the overheat, please don’t plug in the cable for a long time for testing. When you feel the slight warm, please turn it off.
JHSF doesn’t work unless the ambient temperature is below 37F/3 degree C. Please test the cable in a cold environment. HEATIT is registered Trademark by zhukeshi(We didn’t authorize other sellers in Amazon.com).
Suitable for use on plastic and metal water pipes.( including inlet pipe,drain pipe, sewer , palm tree frost protection etc). Self regulating heating cable output will adjust automatically based on the ambient temperature at each point along the cable. No worry about the overheat risk. More Safe. Can be used by straight, spiral and overlap. More functional.
Pre-assembled, easy to install. Including grounded plug with light, built in thermostat(turn the cable 37F on 50F off), and instructions. 120 volt, 3 watts/ft at 50 degrees F. Energy-efficient. Protect pipes up to 2″ in diameter. For a better freeze protection, at least 1/2 inch thick insulation material is recommended, especially for extremely cold weather.
ETL approved. 2 ft 18/3 cold lead with plug. Industrial grade heat shrinkage tube for connection.The lowest installation temperature of this heating cable is -10 degree C. Tough XLPE as inner insulation and weather resistant PE (high-low temperature) as out jacket. Ingress Protection 65. Durable
Testing the cable before the installation. Uncoil the cable, plug in the heating cable and then put the thermostat part of the cable into an ice bucket for few minutes. When the temperature is below 37F, the thermostat will energize the cable to work. Normally you can feel the slight warm on the heating cable in few minutes. Four year limited warranty. If you are not completely satisfied with HEATIT heating cable, please feel free to contact us in any time, we’ll try our best to solve your issue
3. Frost King HC30A Heating Cables, 30 Feet, Black
HEATIT is registered Trademark by zhukeshi(We didn’t authorize other sellers in Amazon.com). Suitable for use on plastic and metal water pipes( including inlet pipe,drain pipe, sewer, palm tree frost protection etc). Industrial grade self regulating heating cable. The cable output will adjust automatically based on the ambient temperature at each point along the cable. No worry about the overheat risk. More Safe. Can be used by straight, spiral and overlap. More functional.
Protect pipes up to 2 1/2” in diameter. For a better freeze protection, at least 1/2 inch thick or thicker insulation material is recommended, especially for extremely cold weather. If the ambient temperature is lower than -20°F(-29°C), please use 1” thick insulation material.
ETL approved. 50 degrees F for pipe freeze protection.3 ft 18/3 cold lead with grounded plug.
Roof deicing application: Can be used on flat roofs, metal roofs, asphalt roofs, rubber roofs, slate roofs, stone roofs, metal roofs, ceramic roofs, composite (tar and gravel) roofs and so on. Rated 10W/ft at 32°F (0°C) for roof deicing. For roof deicing application, you may need to buy clips and hangers separately. For the circuit breaker requirement especially for the cables which length is over 100ft, please check the listed picture.
Testing the cable before the installation. Uncoil the cable, plug in the heating cable. Normally you can feel the slight warm on the heating cable in few minutes. Two year limited warranty – If you are not completely satisfied with HEATIT heating cable, please feel free to contact us in any time, we’ll try our best to solve your issue.
This item is a M-D Building Products 4309 3-Foot Pipe Heating Cable with Thermostat
Purpose of use for Rough Plumbing, pipe-heat-cables
This product is manufactured in China
Prevents frozen water pipes to -50°F
Easy to install just “wrap around” application
Sensor light shows thermostat is working
Available in 6 different lengths
Built in thermostat
Description
Product Description
This item is a M-D Building Products 4309 3-Foot Pipe Heating Cable with Thermostat. Purpose of use for Rough Plumbing, pipe-heat-cables. This product is manufactured in China.
From the Manufacturer
M-d building products 04309 3′ pipe heating cable with thermostatm-d building products 04309 3′ pipe heating cable with thermostat features: ul and csa approved pipe heating cable designed to prevent water line freeze up ready to install, grounded cord and plug, thermostat controlled, with pilot light 3′. No wrap needed.
SECURED PROTECTION: From 9-11 feet (2.74-3.35 m) and up to 1-1 1/2 inches (25.4-38.1 mm) in diameter.
EASY INSTALLATION: Just put our Icebreaker cable along the pipes to keep ice and coldness away (Recommended for use on water-filled metal and rigid plastic pipes).
ENERGY SAVING THERMOSTAT CONTROLLED: The built-in thermostat can sense the temperature of the pipe. It turns the cable on at 38°F and turns it off automatically when the pipe has been heated to a temperature of approximately 45°F.
ECONOMICAL: Reliable low wattage design saves up to 70% energy than other cables and protects your cable to -50°F.
DURABLE: Weather resistant PVC outer jacket and inner insulation. It will operate for years without requiring maintenance.
Description
Size:9FeetX2
Say goodbye to frozen pipes in the winter with the GardenHOME Pipe Heating Cable – 9ft. with Thermostat, designed for preventing water pipes from freezing. This temperature-controlled cable runs along the pipes and valves, thawing frozen pipes. The build-in thermostat will sense the temperature of the pipe and turn the cable on and off, while only using five amps of electricity or less, to provide the most economical solution for frozen pipe disasters.
*Our Pipe Heating Cable & Ice Melting Cable prevents your pipes from major repair costs due to cold weather, snow or frozen water damage.
*This quick and easy ice-melting kit is ideal for indoor and outdoor use.
*It is winter and Subzero resistant, durable and long lasting due to its unique material composition. This Kit prevents congestions and ice backups.
*It is easy to install by using the included mounting hardware. It operates for years without requiring maintenance.
HOW IT WORKS
It is thermostat controlled. The built-in thermostat can sense the temperature of the pipe. It turns the cable on at 38°F and turns it off automatically when the pipe is heated to a temperature of approximately 45°F.
APPLICATION AREA
Used on pipes in House, Garage, Pipes, Garden, Patio and many more!
FEATURES
• Pre-assembled for easy installation • Protects pipes from 9-11 feet and up to 1-1.5 inches in diameter • Use on water-filled plastic and metal pipes only • Economical solution to frozen pipe disasters • Weather resistant PVC outer jacket and inner insulation
ABOUT US GardenHOME stands for highest quality to the lowest price. We give 30-days MONEY BACK PROMISE! If you are not 100% satisfied!
HEATIT is registered Trademark by zhukeshi(We didn’t authorize other sellers in Amazon.com). Suitable for use on plastic and metal water pipes( including inlet pipe,drain pipe, sewer, palm tree frost protection etc). Industrial grade self regulating heating cable. The cable output will adjust automatically based on the ambient temperature at each point along the cable. No worry about the overheat risk. More Safe. Can be used by straight, spiral and overlap. More functional.ETL approved.
Fluoropolymer (Industrial grade: One of the most heavy duty plastic material) as the outer jacket. JHSF1-CT cables are configured for use in nonhazardous and hazardous locations, including areas where corrosives may be present. Exposure to organic chemicals or corrosives. Can be used underwater application. Please keep the connection (Meet water proof IP65) between the orange cold lead and black heating cable above the water level. The black heating cable including end seal meet water proof IP68
Protect pipes up to 2 1/2″ in diameter. For a better freeze protection, at least 1/2 inch thick or thicker insulation material is recommended, especially for extremely cold weather. If the ambient temperature is lower than -20°F(-29°C), please use 1″ thick insulation material. Pre-assembled, Including grounded plug with light, easy to install install and use without built in thermostat. 120 volt, 5 watts/ft at 50 degrees F for pipe freeze protection. 6ft 18/3 cold lead with grounded plug.
Roof deicing application: Can be used on flat roofs, metal roofs, asphalt roofs, rubber roofs, slate roofs, stone roofs, metal roofs, ceramic roofs, composite (tar and gravel) roofs and so on. Rated 10W/ft at 32°F (0°C) for roof deicing. For roof deicing application, you may need to buy clips and hangers separately.
Testing the cable before the installation. Uncoil the cable, plug in the heating cable Normally you can feel the slight warm on the heating cable in few minutes. Ten year limited warranty – If you are not completely satisfied with HEATIT heating cable, please feel free to contact us in any time, we’ll try our best to solve your issue.
Conclusion
By our suggestions above, we hope that you can found Heatit Pipe Heating 30Ft for you.Please don’t forget to share your experience by comment in this post. Thank you!
JHSF doesn’t work unless the ambient temperature is below 37F/3 degree C. Please test the cable in a cold environment. HEATIT is registered Trademark by zhukeshi(We didn’t authorize other sellers in Amazon.com).
Suitable for use on plastic and metal water pipes.( including inlet pipe,drain pipe, sewer , palm tree frost protection etc). Self regulating heating cable output will adjust automatically based on the ambient temperature at each point along the cable. No worry about the overheat risk. More Safe. Can be used by straight, spiral and overlap. More functional.
Pre-assembled, easy to install. Including grounded plug with light, built in thermostat(turn the cable 37F on 50F off), and instructions. 120 volt, 3 watts/ft at 50 degrees F. Energy-efficient. Protect pipes up to 2″ in diameter. For a better freeze protection, at least 1/2 inch thick insulation material is recommended, especially for extremely cold weather.
ETL approved. 2 ft 18/3 cold lead with plug. Industrial grade heat shrinkage tube for connection.The lowest installation temperature of this heating cable is -10 degree C. Tough XLPE as inner insulation and weather resistant PE (high-low temperature) as out jacket. Ingress Protection 65. Durable
Testing the cable before the installation. Uncoil the cable, plug in the heating cable and then put the thermostat part of the cable into an ice bucket for few minutes. When the temperature is below 37F, the thermostat will energize the cable to work. Normally you can feel the slight warm on the heating cable in few minutes. Four year limited warranty. If you are not completely satisfied with HEATIT heating cable, please feel free to contact us in any time, we’ll try our best to solve your issue
2. Frost King HC30A Heating Cables, 30 Feet, Black
Easy Heat AHB-019 9′ Pipe Heating CableEasy Heat AHB-019 9′ Pipe Heating Cable Features: Tough PVC inner insulation Continuous ground braid Weather resistant PVC outer jacket Energy saving Thermostat is located between cold lead and heating cable 2′ 18/3 cold lead with grounded plug 63 watts 120 volts AC 9′ heated section
From the Manufacturer
Temperature-controlled cable runs straight along pipe and valves, held in place by application tape and plugs into grounded electrical outlet. Keeps water flowing down to -380. For odd lengths of pipe over 3/4 inches in diameter, we recommend two separate cables on opposite sides of the pipe with up to 3 feet of overrun at center of pipe run. Metal pipe requires 1/2-inch fiberglass insulation around cable. For plastic pipe, its recommended wrapping pipe with aluminum foil before cable installation. The traditional resistance cable produces a fixed amount of heat based on the electrical line feed. It comes with a built-in thermostat that switches the flow of electricity on and off based on temperature. 120 volts. 7 watts per foot. Not U.L. Listed.
7. M-D Building Products 4309Pipe Heating Cable with Thermostat, 3-Foot
This item is a M-D Building Products 4309 3-Foot Pipe Heating Cable with Thermostat
Purpose of use for Rough Plumbing, pipe-heat-cables
This product is manufactured in China
Prevents frozen water pipes to -50°F
Easy to install just “wrap around” application
Sensor light shows thermostat is working
Available in 6 different lengths
Built in thermostat
Description
Product Description
This item is a M-D Building Products 4309 3-Foot Pipe Heating Cable with Thermostat. Purpose of use for Rough Plumbing, pipe-heat-cables. This product is manufactured in China.
From the Manufacturer
M-d building products 04309 3′ pipe heating cable with thermostatm-d building products 04309 3′ pipe heating cable with thermostat features: ul and csa approved pipe heating cable designed to prevent water line freeze up ready to install, grounded cord and plug, thermostat controlled, with pilot light 3′. No wrap needed.
SECURED PROTECTION: From 9-11 feet (2.74-3.35 m) and up to 1-1 1/2 inches (25.4-38.1 mm) in diameter.
EASY INSTALLATION: Just put our Icebreaker cable along the pipes to keep ice and coldness away (Recommended for use on water-filled metal and rigid plastic pipes).
ENERGY SAVING THERMOSTAT CONTROLLED: The built-in thermostat can sense the temperature of the pipe. It turns the cable on at 38°F and turns it off automatically when the pipe has been heated to a temperature of approximately 45°F.
ECONOMICAL: Reliable low wattage design saves up to 70% energy than other cables and protects your cable to -50°F.
DURABLE: Weather resistant PVC outer jacket and inner insulation. It will operate for years without requiring maintenance.
Description
Size:9FeetX2
Say goodbye to frozen pipes in the winter with the GardenHOME Pipe Heating Cable – 9ft. with Thermostat, designed for preventing water pipes from freezing. This temperature-controlled cable runs along the pipes and valves, thawing frozen pipes. The build-in thermostat will sense the temperature of the pipe and turn the cable on and off, while only using five amps of electricity or less, to provide the most economical solution for frozen pipe disasters.
*Our Pipe Heating Cable & Ice Melting Cable prevents your pipes from major repair costs due to cold weather, snow or frozen water damage.
*This quick and easy ice-melting kit is ideal for indoor and outdoor use.
*It is winter and Subzero resistant, durable and long lasting due to its unique material composition. This Kit prevents congestions and ice backups.
*It is easy to install by using the included mounting hardware. It operates for years without requiring maintenance.
HOW IT WORKS
It is thermostat controlled. The built-in thermostat can sense the temperature of the pipe. It turns the cable on at 38°F and turns it off automatically when the pipe is heated to a temperature of approximately 45°F.
APPLICATION AREA
Used on pipes in House, Garage, Pipes, Garden, Patio and many more!
FEATURES
• Pre-assembled for easy installation • Protects pipes from 9-11 feet and up to 1-1.5 inches in diameter • Use on water-filled plastic and metal pipes only • Economical solution to frozen pipe disasters • Weather resistant PVC outer jacket and inner insulation
ABOUT US GardenHOME stands for highest quality to the lowest price. We give 30-days MONEY BACK PROMISE! If you are not 100% satisfied!
10. Heat Cable for Pipe Freeze Protection, 60 feet, with Built-in Thermostat and 16 Feet of High-Temp Installation Tape, Heavy-Duty, Self-Regulating, 120 volt
THIS CABLE WILL NOT TURN ON UNLESS IT IS IN A COLD ENVIRONMENT. We’ve received a couple bad reviews from people testing the cables in their living rooms. Please don’t be that guy.
AMERICAN SUPPORT: Knowledgeable, Minnesota-based company with expert support staff you can actually speak to! We are excited to help with your installation questions. Phone: 877-387-4218, or email us at [email protected]
TAPE INCLUDED: 16 feet of high-temperature glass cloth tape is included with this cable.
HEAVY DUTY: Integrated thermostat turns cable on at 37 degrees, off at 50 degrees, greatly reducing energy waste. Cable is 8mm wide and includes a 24” unheated cord (add to stated cable length). Cable has commercial-grade outer jacket for long life and carries a FOUR YEAR WARRANTY, which is double the warranty of similar cables on Amazon. Will not short or burn out if cable is overlapped.
USES: Use on the inside or outside of all types of water carrying pipe including copper, steel, PVC, ABS, PEX, concrete and more
can be exposed directly to water and is rated for soil contact.
Description
Size:60 Feet
THIS CABLE WILL NOT WORK unless it is in a cold environment. We’ve received a couple bad reviews because people ‘tested’ the cable in their warm living room. Eye roll. Please don’t be that guy. The built-in thermostat will NOT TURN THE CABLE ON unless it is in a cold environment. Now for the good news, this kit includes 16 feet of high temperature glass cloth tape for installing your cable. Pipe Freeze Pro is a commercial-grade, self-regulating heat cable which provides years of reliable freeze protection for pipes of all varieties, including copper, steel, PVC, ABS, PEX and more (pipe diameters up to 2”). It may also be used in drains and culverts through the winter months to promote drainage. Don’t buy from companies without a human available by phone. Heat cable is technical stuff and it’s great to have solid advice on how to install it. We are the only heat cable seller on Amazon who is a simple phone call away. Phone: 877-387-4218. Eat that off shore competitors! Pipe Freeze Pro is jacketed with a commercial-grade fluoropolymer and comes standard with a flame-retardant thermoplastic interior jacket. Our 16 gauge heating wires are 200% thicker than the conductors found in cheap, constant wattage cables like EasyHeat and Frost King. Thicker conductors mean greater heating efficiency, more melting power and long term cable integrity. Pipe Freeze Pro is self-regulating, meaning it ‘asks’ for more energy as it gets colder outside and less energy when it’s warmer. The entire length of our cable is temperature sensitive such that colder areas demand more power than warmer areas. Smart stuff. The stated cable length DOES NOT include an additional 24” unheated cold lead. For example, a 6 foot cable is 6 feet plus 2 feet of unheated cord. Installation is simple. Run Pipe Freeze Pro along the pipe, secure with fiberglass cloth tape (included) every 12 inches and wrap with standard pipe insulation. Read the manual for full instructions, of course.
Conclusion
By our suggestions above, we hope that you can found Heatit Pipe Heating 30Ft for you.Please don’t forget to share your experience by comment in this post. Thank you!
JHSF doesn’t work unless the ambient temperature is below 37F/3 degree C. Please test the cable in a cold environment. HEATIT is registered Trademark by zhukeshi(We didn’t authorize other sellers in Amazon.com).
Suitable for use on plastic and metal water pipes.( including inlet pipe,drain pipe, sewer , palm tree frost protection etc). Self regulating heating cable output will adjust automatically based on the ambient temperature at each point along the cable. No worry about the overheat risk. More Safe. Can be used by straight, spiral and overlap. More functional.
Pre-assembled, easy to install. Including grounded plug with light, built in thermostat(turn the cable 37F on 50F off), and instructions. 120 volt, 3 watts/ft at 50 degrees F. Energy-efficient. Protect pipes up to 2″ in diameter. For a better freeze protection, at least 1/2 inch thick insulation material is recommended, especially for extremely cold weather.
ETL approved. 2 ft 18/3 cold lead with plug. Industrial grade heat shrinkage tube for connection.The lowest installation temperature of this heating cable is -10 degree C. Tough XLPE as inner insulation and weather resistant PE (high-low temperature) as out jacket. Ingress Protection 65. Durable
Testing the cable before the installation. Uncoil the cable, plug in the heating cable and then put the thermostat part of the cable into an ice bucket for few minutes. When the temperature is below 37F, the thermostat will energize the cable to work. Normally you can feel the slight warm on the heating cable in few minutes. Four year limited warranty. If you are not completely satisfied with HEATIT heating cable, please feel free to contact us in any time, we’ll try our best to solve your issue
2. Frost King HC30A Heating Cables, 30 Feet, Black
HEATIT is registered Trademark by zhukeshi(We didn’t authorize other sellers in Amazon.com). Suitable for use on plastic and metal water pipes( including inlet pipe,drain pipe, sewer, palm tree frost protection etc). Industrial grade self regulating heating cable. The cable output will adjust automatically based on the ambient temperature at each point along the cable. No worry about the overheat risk. More Safe. Can be used by straight, spiral and overlap. More functional.
Protect pipes up to 2 1/2” in diameter. For a better freeze protection, at least 1/2 inch thick or thicker insulation material is recommended, especially for extremely cold weather. If the ambient temperature is lower than -20°F(-29°C), please use 1” thick insulation material.
ETL approved. 50 degrees F for pipe freeze protection.3 ft 18/3 cold lead with grounded plug.
Roof deicing application: Can be used on flat roofs, metal roofs, asphalt roofs, rubber roofs, slate roofs, stone roofs, metal roofs, ceramic roofs, composite (tar and gravel) roofs and so on. Rated 10W/ft at 32°F (0°C) for roof deicing. For roof deicing application, you may need to buy clips and hangers separately. For the circuit breaker requirement especially for the cables which length is over 100ft, please check the listed picture.
Testing the cable before the installation. Uncoil the cable, plug in the heating cable. Normally you can feel the slight warm on the heating cable in few minutes. Two year limited warranty – If you are not completely satisfied with HEATIT heating cable, please feel free to contact us in any time, we’ll try our best to solve your issue.
4. M-D Building Products 4309Pipe Heating Cable with Thermostat, 3-Foot
This item is a M-D Building Products 4309 3-Foot Pipe Heating Cable with Thermostat
Purpose of use for Rough Plumbing, pipe-heat-cables
This product is manufactured in China
Prevents frozen water pipes to -50°F
Easy to install just “wrap around” application
Sensor light shows thermostat is working
Available in 6 different lengths
Built in thermostat
Description
Product Description
This item is a M-D Building Products 4309 3-Foot Pipe Heating Cable with Thermostat. Purpose of use for Rough Plumbing, pipe-heat-cables. This product is manufactured in China.
From the Manufacturer
M-d building products 04309 3′ pipe heating cable with thermostatm-d building products 04309 3′ pipe heating cable with thermostat features: ul and csa approved pipe heating cable designed to prevent water line freeze up ready to install, grounded cord and plug, thermostat controlled, with pilot light 3′. No wrap needed.
HEATIT is registered Trademark by zhukeshi (We didn’t authorize other sellers in Amazon.com). HTM self-regulating pipe heating cable system is designed for mobile home and other dry applications etc. Can be used on residential metal or plastic water supply and drain pipe freezing protection.
ETL approved. Tinned copper braid as the out jacket as well as electrical ground. Self regulating heating cable just deliver the heat where is need. The cable output will adjust automatically based on the ambient temperature at each point along the cable. No worry about overheat risk. More Safe. Can be used by straight, spiral and overlap. More functional.
Additional tools which you may need: High quality electrician’s tape such as HEATIT glass cloth tape, 1/2” thick fiberglass insulation with vapor seal, wire cutters or heavy scissors, Phillips#2 slotted screw drivers, Ruler or measuring tape.
HEATIT HTM connection kit is necessary for the pipe freeze protection application. Please purchase this kit separately.
Quick test: Once insulation is finished, plug the cable into a 120V AC outlet. Don’t use any of the water for about 1 hour. After that turn on the tap on HEATIT HTM protected pipe and test the water temperature. You should feel the slight warm from the water.Three year limited warranty. If you are not completely satisfied with HEATIT heating cable, please feel free to contact us in any time, we’ll try our best to solve your issue
Easy Heat AHB-019 9′ Pipe Heating CableEasy Heat AHB-019 9′ Pipe Heating Cable Features: Tough PVC inner insulation Continuous ground braid Weather resistant PVC outer jacket Energy saving Thermostat is located between cold lead and heating cable 2′ 18/3 cold lead with grounded plug 63 watts 120 volts AC 9′ heated section
From the Manufacturer
Temperature-controlled cable runs straight along pipe and valves, held in place by application tape and plugs into grounded electrical outlet. Keeps water flowing down to -380. For odd lengths of pipe over 3/4 inches in diameter, we recommend two separate cables on opposite sides of the pipe with up to 3 feet of overrun at center of pipe run. Metal pipe requires 1/2-inch fiberglass insulation around cable. For plastic pipe, its recommended wrapping pipe with aluminum foil before cable installation. The traditional resistance cable produces a fixed amount of heat based on the electrical line feed. It comes with a built-in thermostat that switches the flow of electricity on and off based on temperature. 120 volts. 7 watts per foot. Not U.L. Listed.
Conclusion
By our suggestions above, we hope that you can found Heatit Pipe Heating 30Ft for you.Please don’t forget to share your experience by comment in this post. Thank you!
