672 reviews analysed
1. DC 12V-24V 1000W 50 A ZVS Low Voltage High Frequency Induction Heating Module Board with Tesla Coil and Cooling Fan
Feature
- Input voltage DC 12V ~ 40V, maximum input current 50A (short), recommended Input voltage range DC 24V ~ 36V
- The power supply used for heating must be large enough
- Using a protective power supply, don’t use battery or battery power
- For long time use, brass tube with water must be used for cooling
- This one is mainly used for heating
Description
Note: It is the working voltage work, the input voltage when the coil is connected or heated. Not the no load voltage. When 12V for power supply, the current should be no less than 20A; when 24V for power supply, the current should be no less than 30A; when 36V for power supply, the current should be no less than 50A. For long time use, brass tube with water must be used for cooling.Output port copper cylinder can most install copper tube of 10mm diameter; when the copper diameter is no more than 4mm, you can solder the copper tube on the clip then fix the copper cylinder; when the diameter is no more than 2mm, it can be connected with output terminal.
This one is mainly used for heating, suitable for the heating power is less than 300W.
Specifications:
Input Voltage: DC 12-40V
Max Input Current: 50A (short time)
PCB Size: 16.5 x 11.2cm/6.5 x 4.4 inch
Board thickness: 0.16cm/0.063inch(only board)
Weight: 780g
Package Included:
1 x induction heating module
1 x brass tube
1 set x brass cylinder and screw
2. 1000W 20A ZVS Low Voltage Induction Heating Board Module Tesla with Coil 12V-48V Flyback Driver Heater DIY
Feature
- 12-48V low voltage power supply. Maximum current 20A, Maximum power 1000W.The bigger voltage, the higher power.
- Tested 53V power supply when working properly. It can be used for DIY players to make small parts quenching, annealing and other heat treatment, heating fast, very convenient
- This circuit can do induction heating, or replace copper tube with high frequency transformer, it will be a powerful inverter
- The higher voltage, the higher current when heating the same things, the effect is better, but at the same time heating is also higher, therefore the choice of input voltage is based on your need.24V or 36V power supply is enough
- Note: buyer need to bring their own power and cooling unit
Description
Features:
24V input with no load current of 3A , 48V input with no load current of 6A
buyer need self-provided power and water cooling device
This circuit can do induction heating, or replace copper tube with high frequency transformer, it will be a powerful inverter
Note:
The kit contains a full set of driving circuit elements and brass
Buyers need to bring their own power and cooling unit.
The circuit board using double-sided fiberglass board, mainly copper traces are used to widen use the entire back surface of the resonant circuit common, continuous work, please add a fan to blow down from above, to the resonance capacitors and other components cool.
The use of switching power supply Please note that due to high power are generally slow start function, which just opened machine output voltage is slowly rising, while it is turned on before the induction heating circuit if the voltage rises to 12V, because start insufficient voltage can not afford to vibration, resulting in two simultaneous conduction mos tube so burned components.
So the first will start switching power supply voltage reaches 12V above and then access the induction heating circuit.
The volume of the object being heated inside the heating coil can not exceed 1/5 of the volume (if the heating cylinder, then heating coil diameter less than the diameter of 1/3), or it may be due to overload or burn out the power supply to the circuit.
Although this circuit can tolerate 20-30A input current moment, but do not exceed 15A when safe work, you can easily add an ammeter between the power supply and heating driver board but always monitor the current overload
Package Includes:
1 x 20A 1000W Flyback driver inductive heater Zero Voltage Switching Tesla
1 x Coil
3. 1800W ZVS Induction Heating Board Module Low Voltage High Frequency 12-48V Flyback Driver Heater with Tesla Coil and Cooling Fan
Feature
- The induction heating boards maximum power is 1800W, adopted super PCB layout design and super heat sink, heat dissipation good, since with a cooling fan interface, can also do Tesla discharge, generator voltage inverter, etc
- The induction heating circuit adopt 12-48V DC power supply, maximum current is 40A, the power uo to 1800W. It can work continuously under the condition of good heat dissipation. moderate power which make it can be used to quenching, annealing and other heat treatment. also for melted with graphite crucible kim/silver/ copper/aluminum and so on, heating is evenly and fast
- it is recommended that not exceed 48V 35A to prevent accidents and damage,Although withstand more than 40A current.Induction heating is recommended to use 36V 20A power supply, 12V power supply is too small almost without response, and 12V power might lead to the voltage decreases, which is very dangerous.More than 24V/20A power supply, the greater the voltage/current, the greater the heating power, heating faster.
- please check the power output meets the requirements if the MOS tube fever,and be sure to do a good job of cooling.Do not empty the board, otherwise it will create a very high noise, then MOS tube will burn out
- please do not to heat too large metal, otherwise it may be overloaded, please add a 35A fuse or ammeter and air switch for better use (not included).
Description
Specification:
Product size:Approx.180x90x80mm (please allowed 1-3mm error)
Heater ring inner:70mm (Recommended crucible+quartz suit,maximum support of 58mm crucible)
Power supply:
New style :AC 100-220V Adapter
Old style: Main board Input voltage: 12V-48V recommend: 36V above
Power requirements: less than 12V≥10A , 15V above≥15A
NOTE:New style and Old style shipped by randomly!!!
It doesn’t affect the performance of product.!!!
Maximum power: 1800W
Maximum current: 40A
Package Content:
1 x PCB board
1 x 48V copper tube
1.The power of heating is very large, except that the plate and components are hot, and the heat of copper tube is very high. you can buy a small water pump and 2 meters of rubber hose(inner diameter is 4mm) for build a water cooling system
Please pay attention to using switch power supply, because output voltage is slowly rising, and if the voltage rise to 10V before connected induction heating circuit that will be lead to circuit can’t afford to vibrate caused by lacking voltage,so that the two MOS tube conduction and components will burned
comes with heating circle diameter-60 mm/design voltage-36V,if you use more than 40V Devices shall be used ≥70 mm diameter heating ring, DC 12V water pump use, please use separate power supply voltage regulator module to avoid fan and water pump are burn out
The minimum input is 12V, but it doesn’t mean all 12V power supply available,The module has specific requirements on voltage and current , 12V require current must than 10A ,output power will greatly reduced if the power is too low ,which will lead to two MOS conduction at the same time & burn MOS tube when lower than 12V
4. fosa 1800W Induction Heating Module ZVS Low Voltage 12V-48V Induction Heating Board Flyback Driver Heater DIY High Frequency Induction Heating Machine Module
Feature
- This product has a maximum power of 1800W, super PCB layout design and super heat sink, superior heat dissipation effect
- 12-48V low voltage DC power supply with a maximum current of 40A. It can work continuously for several hours with good heat dissipation
- Can use graphite crucible to melt gold, silver, copper, aluminum and other metals, heating evenly, fast and very convenient
- With a cooling fan interface, can also do Tesla discharge, generator voltage inverter, etc
- It is recommended not to exceed 48V 35A to prevent accidents and damage
Description
Specification:
Input Voltage: 12V-48V (Recommendation: above 36V)
Power Requirments: Less than 12V >=10A, More than 15V >=15A
Maximum Power: 1800W
Maximum Current: 40A
Heater Inner Ring: 70mm / 2.8in
Size: 18 * 12 * 9 cm / 7.1 * 4.7 * 3.5in
Weight: Approx. 1052g
Package Included:
1 x PCB Board
1 x Copper Tube
Note:
1. When using a switching power supply, make sure that the power supply voltage is stable before connecting to the induction heating circuit.
2. Do not heat metal that is too large or it may be overloaded. Please add a 35A fuse or ammeter.
3. Although this driver board can withstand more than 40A, it is recommended not to exceed 48V 35A to prevent accidents and damage.
4. The minimum input voltage of the module is 12V, the voltage of 12V must be greater than 10A to use the power supply.
5. If you find that the MOS tube is hot, first consider whether the power output meets the requirements.
6. Do not clear the circuit board, otherwise it will emit a very high frequency of noise, and then the MOS tube will burn out.
7. It is recommended to use a 36V 20A power supply. Below 12V is very dangerous.
5. Amaze-Heater SOLO 400-Watt Electric Convection Room Heater – AH400USS
Description
Amaze-Heater SOLO 400 Watt electric convection room heaters are crafted to perfection with beveled edges and an attractive dome sticker, giving it a very unique and stylish appearance. Amaze-Heaters are the safest in their class as there are no moving parts with no gas and no exposed heating elements. These heaters will allow you to save up to 50% or more on your heating cost. Instead of heating an object or person, the heater uses efficient convection technology to warm an entire room up to 150 square feet depending on room insulation. Its ultra slim and compact design allows for discreet out-of-the way wall mounting and installs quickly and easily with the included installation hardware. Once installed, the heater can be painted to match the room decor and will operate silently. As the heater will not dry the air or burn up the oxygen in the room, you will experience warm, comfortable, efficient, safe and silent heating all season long. Come home to the warmth of Amaze Heater.
6. Homeleader Electric Panel Heater, 1500 Watt Space Heater with Remote Control and LED Touch Button, Free Standing Room Heater, GH-15F (White)
Feature
- AMAZING PERFORMANCE: High power of 1500 watts warms the room in a very short time which saves power and time.
- PERFECT DESIGN: Attractive design – black crystal glass panel look like a TV. This stylish panel heater is perfect for any application and any decor. With its slim design, you can virtually put this heater anywhere.
- HIGH FLEXIBILITY AND CONVENIENCE: LED display remote control and 24h timer provide you with unlimited convenience. You can control the panel heater either through LED touch screen or remote control.
- HIGH QUALITY: X-shaped aluminum heating element for quick heating-up. The heater is equipped with electronic sensor thermostat and overheat protection which guarantee the long lifespan
- 【ATTENTION】This panel heater does not include the wall mount bracket,so if you need this, please purchase it separately. And if you don’t know how to use the panel heater, can also download the electronic user manual in the detail page.
Description
Homeleader: The best choice for your daily life
Homeleader GH-15F Glass Panel convection heater of Continental style, a new product based on high-tech, featuring a novel style, quick heating, high thermal efficiency, security, no noise, no open flame, long life and simple maintenance.
Main Features
It is silent warmth: quiet and cozy
Operation function of touch switch and remote control, easy to use
Display panel of digital screen, infrared remote control, automatic determination of ambient temperature, multi-temperature control security setting, easy and simple
Convection heater features a heating element with aluminum heat sink, long-life
Overheat protection and tip-over power off design and ensures user safe
Mode
1. Comfortable Mode
Only when the preset temperature must be higher than room temperature, the heater will work in full power.
2. Economical Mode
The preset temperature must be higher than the room temperature, the heater will work in half-power.
3. ECO Mode
In this mode, the heater temperature will maintain at 66.2-69.8℉. If room temperature is higher than this range, the heater will stop working; otherwise, it will automatically switch back to ECO mode.
4. Frost-Free Mode
When room temperature is below 41℉, the heater will be on automatically; when the temperature reaches 44.6℉, the heater will stop heating. (Not for heating, this mode is used for frost prevention.)
Specifications:
Brand: Homeleader
Model Number: GH-15F(White)
Rate Power: 1500W
Rate voltage: 120V 50/60Hz
Use: Bedroom, Living Room
Product Dimensions: 27.56 x 3.94 x 18.50 inch
Package Size: 29.13 x 5.51 x 21.26 inch
Package Weight: 19.2lbs
Conclusion
By our suggestions above, we hope that you can found Sainsmart1000w Zvs Low Voltage Induction Heating Board for you.Please don’t forget to share your experience by comment in this post. Thank you!
